041-356 富士胶片彩色复印机Apeos C3070 3570 4570 5570 6570 故障代码

[复制链接]
查看399 | 回复0 | 2024-03-01 15:57:49 | 显示全部楼层 |阅读模式
故障代码查询
设备分类: 复印机 » 富士胶片复印机 » Apeos C7070 / C6570 / C5570 / C4570 / C3570 / C3070
故障代码: 041-356
故障解释: (Mid/High model) Motor Drive PWB F11 Fuse Fail
故障原因: Description
Fuse 11 on the Motor Drive PWB has blown
故障排查: Procedure
Turn OFF the power and disconnect the power plug. Remove the Rear Lower Cover. Measure the resistance of the Motor Drive PWB (F11).
Is the resistance 5 Ohm or higher?
Y N
Check the connection between the LVPS_CP1U J509-2 and the Motor Drive PWB J400-1 for open circuit, short circuit, and poor contact.
Disconnect the following connectors from the Motor Drive PWB and measure the resistance between each connector terminal and the GND.
 J411-3 (1ST BTR CONT/RET Sensor)
 J416-4 (Temp & Humidity Sensor)
 J416-12 (ADC Sensor)
 J417-3 (Toner Bottle Position Sensor)
 J417-6 (Toner Bottle Full Sensor)
 J418-18 (ATC Sensor Y)
 J420-1 (Fusing Unit Exit Sensor)
 J420-4 (P/Roll Latch Sensor)
 J420-9 (Belt Speed Sensor)
 J424-3 (ATC Sensor K)
 J424-6 (ATC Sensor M)
 J424-9 (ATC Sensor C)
 J425-5 (T1 Level Sensor)
 J425-8 (T1 No Paper Sensor)
 J425-11 (T1 Lever Position Sensor)
 J425-16 (T1 Pre Feed Sensor)
 J428-4 (T2 No Paper Sensor)
 J428-9 (T2 Pre Feed Sensor)
 J428-10 (T2 Lever Position Sensor)
 J428-1 (T2 Level Sensor)
 J431-B6 (Regi Sensor)
 J431-B9 (POB Jam Sensor)
 J431-B12 (MSI Feed Out Sensor)
 J433-3 (Exit2 Sensor)
 J433-4 (Exit2 OCT Home Position Sensor)
 J433-12 (Face Up Exit Sensor)
 J433-17 (Exit1 OCT Full Stack Sensor)
 J435-1 (Exit1 OCT Home Position Sensor)
 J435-6 (Exit2 Tray Sensor)
 J435-10 (NOHAD Temp & Humidity Sensor)
 J435-13 (Exit1 Tray Sensor)
 J436-A4 (MSI No Paper Sensor)
 J436-A7 (MSI Nudger Position Sensor)
 J443-6 (Rear ReC Sensor)
 J443-12 (Front ReC Sensor)
 J451-1 (Feed Out Sensor 3)
 J451-4 (T3 Level Sensor)
 J451-7 (T3 No Paper Sensor)
 J451-12 (T3 Pre Feed Sensor)
 J451-13 (T3 Lever Position Sensor)
 J452-9 (2TM Take Away Motor)
 J454-5 (TTM Feed Out Sensor 4)
 J454-6 (T4 Level Sensor)
 J454-9 (T4 No Paper Sensor)
 J454-14 (T4 Pre Feed Sensor)
 J454-15 (T4 Lever Position Sensor)
Is the resistance 5 Ohm or higher for all?
Y N
Check the following:
 The connections that are in earth fault (at 5 ohm or lower) for short circuits.
 The target components for internal short circuits.
Replace the Motor Drive PWB. (PL 18.2)
说明备注: -

注册或关注公众号后查看更多内容

您需要 登录 才可以下载或查看,没有账号?我要加入

×
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 我要加入

本版积分规则